HI3-0303-5Z
| Parameters | |
|---|---|
| Technology | CMOS |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Polarity | Non-Inverting |
| Temperature Grade | COMMERCIAL EXTENDED |
| Number of Channels | 1 |
| Max Supply Voltage | 34V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 90nA |
| Nominal Supply Current | 90μA |
| Max Supply Current | 500μA |
| Number of Bits | 2 |
| Throw Configuration | SPDT |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| Off-state Isolation-Nom | 60 dB |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 50Ohm |
| Height Seated (Max) | 5.33mm |
| Length | 19.17mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Through Hole |
| Package / Case | CDIP |
| Number of Pins | 14 |
| Packaging | Bulk |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Number of Terminations | 14 |
| Resistance | 50Ohm |
| Max Operating Temperature | 75°C |
| Min Operating Temperature | 0°C |
| Subcategory | Multiplexer or Switches |
HI3-0303-5Z Overview
Shipping overseas is convenient due to the electrical component's packing in CDIP. In order to provide high reliability, an advanced packaging method Bulk is used. A total of 14 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. There are 14 pins injected into the electronic part body. A 50Ohm internal resistance characterizes this multiplexer. To find out what the functions of 14 pins are, please refer to their datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In a normalsituation, users should not supply the switches with voltage higher than 34V. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended to use 5V as the lowest voltage for the electrical part. For this multiplexer to operate, 90nA current would be sufficient. A digital multiplexer may suffer damage if voltage is applied above 500μA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VFor dual power supplies, a voltage of at least 5V should be attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating voltages of 18V are compatible with the electrical part. A temperature above 75°C is not suitable for operation of the analogue multiplexer. The Drain to Source resistance of this electronic component is 50Ohm. 2-bits are supported.
HI3-0303-5Z Features
1 Channels
90nA Supply Current
Drain-to-Source resistance: 50Ohm
2-Bit
HI3-0303-5Z Applications
There are a lot of Intersil (Renesas Electronics America) HI3-0303-5Z Analog Switches & Multiplexers ICs applications.
- Audio and video signal routing
- Avionics and Military Systems
- Digital cross connects (DSX-1)
- SONET/SDH ADM
- Video switching
- Multiplexers
- Cable Modem
- SDH/SONET multiplexers
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Data Acquisition Systems
