banner_page

HI9P0201-5Z

Analog Switches BREAK-BEFORE-MAKE 16 Pins 15V SOIC


  • Manufacturer: Intersil (Renesas Electronics America)
  • Nocochips NO: 391-HI9P0201-5Z
  • Package: SOIC
  • Datasheet: PDF
  • Stock: 370
  • Description: Analog Switches BREAK-BEFORE-MAKE 16 Pins 15V SOIC(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Contact Plating Tin
Mount Surface Mount
Package / Case SOIC
Number of Pins 16
Packaging Bulk
Published 1999
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 3
Number of Terminations 16
Resistance 80Ohm
Max Operating Temperature 75°C
Min Operating Temperature 0°C
Subcategory Multiplexer or Switches
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 1.27mm
Time@Peak Reflow Temperature-Max (s) 40
Pin Count 16
Polarity Non-Inverting
Power Supplies +-15V
Temperature Grade COMMERCIAL EXTENDED
Number of Channels 1
Max Supply Voltage 44V
Operating Supply Current 500μA
Nominal Supply Current 500μA
Max Supply Current 2mA
Number of Bits 4
Throw Configuration SPST
Turn On Delay Time 185 ns
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 220 ns
Max Dual Supply Voltage 22V
Off-state Isolation-Nom 80 dB
Switching BREAK-BEFORE-MAKE
Drain to Source Resistance 55Ohm
Normal Position NC
Height Seated (Max) 1.75mm
Length 9.9mm
Width 3.9mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status RoHS Compliant
Lead Free Lead Free

HI9P0201-5Z Overview


Packed in SOIC, the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Bulk. In total, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. Into the electrical component body are injected 16 pins. This digital multiplexer has 80Ohm internal resistance. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. normally, users should not supply switches with voltages higher than 44V. Analog switch ics with Dual, Single supply type are cost-effective. In order to operate this switch device, it would need a current of 500μA. If you put voltage higher than 2mA on the digital multiplexer, damage may occur. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. Temperatures over 75°C should not be allowed for the multiplexer to operate. The Drain to Source resistance of this electronic component is 55Ohm. 4-bit conductivity is possible.

HI9P0201-5Z Features


1 Channels
500μA Supply Current
Drain-to-Source resistance: 55Ohm
4-Bit

HI9P0201-5Z Applications


There are a lot of Intersil (Renesas Electronics America) HI9P0201-5Z Analog Switches & Multiplexers ICs applications.

  • Public switching systems
  • SONET
  • Audio/video switches
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • Video signal routing
  • Channelized and Unchannelized DS3 applications
  • E1 Network Equipment
  • Optical Applications
  • Imaging
  • Transmit

Write a review

Note: HTML is not translated!
    Bad           Good