ITS4100SSJNXUMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Cut Tape (CT) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 200mOhm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 1.5W |
| Technology | NMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 13.5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Max Output Current | 2A |
| Operating Supply Voltage | 34V |
| Interface | On/Off |
| Nominal Supply Current | 500μA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Turn On Delay Time | 170 μs |
| Switch Type | General Purpose |
| Halogen Free | Halogen Free |
| Nominal Input Voltage | 13.5V |
| Turn-Off Delay Time | 230 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5V~34V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage, UVLO |
| Output Peak Current Limit-Nom | 2A |
| Rds On (Typ) | 70m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Output Current Flow Direction | SINK |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
ITS4100SSJNXUMA1 Overview
As you can see, it's packaged in the way of a Cut Tape (CT).In the 8-SOIC (0.154, 3.90mm Width) package, it is included.The lighting driver is mounted in the Surface Mount position.This switch is of type General Purpose.It is recommended to set the temperature to -40°C~125°C TJ in order to ensure reliable operation.The lighting driver is equipped with 1 outputs that can be used.The LED driving board is powered by a voltage of Not Required.A maximum output voltage of N-Channel volts can be obtained with this LED driver.A total of 8 terminations have been recorded.The operation is carried out using the 8 pins.The LED driving board has a total of 1 functions.To comply with the operation criteria, the maximum output current is reduced to 2A.Using a voltage of 13.5V allows for high efficiency.Surface Mount is mounted in the way.In this case, there is 200mOhm resistance in the LED driving board.The LED driver is packaged in an econtainer with a capacity of Peripheral Drivers.In order to optimize the efficiency of the supply voltage, it should be set to 34V.
ITS4100SSJNXUMA1 Features
Supplied from 13.5V
Resistance of 200mOhm
ITS4100SSJNXUMA1 Applications
There are a lot of Infineon Technologies ITS4100SSJNXUMA1 Power Switches ICs applications.
- Notebook PC
- Notebook and Tablet Computers
- PC Cards
- Storage (HDDs, SSDs)
- Hot-Swap Systems
- Hot Swaps
- USB3.1 Power Delivery
- Portable Music Players
- Portable GPS
- USB Protection
