L6207Q
| Parameters | |
|---|---|
| Voltage - Supply | 8V~52V |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 48V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | L6207 |
| Pin Count | 48 |
| Number of Outputs | 2 |
| Output Voltage | 52V |
| Max Output Current | 5.6A |
| Supply Voltage-Min (Vsup) | 8V |
| Interface | Logic |
| Analog IC - Other Type | STEPPER MOTOR CONTROLLER |
| Nominal Supply Current | 10mA |
| Output Configuration | Half Bridge (4) |
| Output Current | 2.5A |
| Collector Emitter Voltage (VCEO) | 52V |
| Max Collector Current | 2.8A |
| Voltage - Load | 8V~52V |
| Fault Protection | Current Limiting, Over Temperature, UVLO |
| Rds On (Typ) | 280m Ω LS, 340m Ω HS |
| Switching Frequency | 100kHz |
| Motor Type | Brushed |
| Load Type | Inductive |
| Height | 950μm |
| Length | 7.15mm |
| Width | 7.15mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 8 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-VFQFN Exposed Pad |
| Number of Pins | 48 |
| Operating Temperature | -25°C~125°C TJ |
| Packaging | Tray |
| JESD-609 Code | e3 |
| Feature | Bootstrap Circuit |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Applications | DC Motors, Stepper Motors, Voltage Regulators |
| Subcategory | Motion Control Electronics |
| Technology | DMOS |
L6207Q Overview
In order to package H bridge, Tray is used.The 48-VFQFN Exposed Pad package includes H bridge to save money.Bridge driver is possible to improve the reliabilbridge drivery of 8V~52V by increasing the supply voltage.H bridge circuit is mounted on Surface Mount.In order for -25°C~125°C TJ to function normally, motor driver H bridge needs to be kept at a certain temperature.There are lots of uses for H bridge motor driver, including DC Motors, Stepper Motors, Voltage Regulators.Surface Mount is adopted as a technique to mount H gate on the PCB.Bootstrap Circuit is one of full bridges specific characteristics.Transmission lines can be terminated with a termination that matches the characteristic impedance of the line using 48 terminations.In signal interfaces, 48 pins serve as pronged contacts.The L6207 base H bridge ic number is the key to finding more related H bridge ics.H bridge circuit operates with the supply voltage of 48V.This H bridge circuit incorporates an analog IC with the type STEPPER MOTOR CONTROLLER.At a specified ambient temperature, 5.6A is the maximum load current that a power supply can provide.Output and power supply pins have a current of 2.5A.The 48 pins of this bridge driver work together to allow it to perform its specific functions.There is a 2 output on it.H bridge motor drivers in the subcategory Motion Control Electronics have a wide range of similarities.52V is the voltage released by the Hbridge.
L6207Q Features
Available in 48-VFQFN Exposed Pad Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : L6207
L6207Q Applications
There are a lot of STMicroelectronics L6207Q Full Bridge Drivers, Half-Bridge Drivers applications.
- Bipolar stepper motor
- OA equipments
- Voltage Regulators for GPUs
- Small Form-Factor Voltage Regulator Modules
- Voltage Regulators for DDR memory arrays
- Telecom Microprocessor
- Dual DC motor
- VTR
- Industrial Pumps
- Desktop Computers
