LF356M
| Parameters | |
|---|---|
| Lifecycle Status | NRND (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Series | BI-FET™ |
| JESD-609 Code | e0 |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | LF356 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 5mA |
| Nominal Supply Current | 5mA |
| Power Dissipation | 380mW |
| Output Current | 25mA |
| Slew Rate | 12V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | ±15V |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 5MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Programmable Power | NO |
| Input Offset Current-Max (IIO) | 0.00002μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
LF356M Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. There are two types of operational amplifiers in this circuit. Instrumentation amplifier is delivered in a Tube case. The number of terminations is approaching the 8 mark. There are a total of 8 pins on this op amp. Please take in mind that this instrumentation amplifier should be run at 15V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. A total of 8 pins are present on the instrumentation amplifier. There is an input offset voltage of 10mV for this buffer op amp. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, this op amp functions well at 0°C~70°C. This op amp can operate from a supply current at 5mA. You should keep the voltage gain at 106.02dB for the time being. The op amp ic has 1 channels on it. The operating supply voltage of instrumentation amplifier is rated 18V voltage. BI-FET? corresponds to the op amp's series.
LF356M Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
LF356M Applications
There are a lot of Texas Instruments LF356M Instrumentational OP Amps applications.
- Proportional counter tubes
- Ultrasound transducers
- Signal transformation
- RF cable systems
- Strain gauges
- Navigation
- PDA
- Blood pressure sensors
- Medical instruments
- Measurements of Wheatstone bridge
