LT1495HS8#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2001 |
| Series | Over-The-Top® |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1495 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Number of Circuits | 2 |
| Operating Supply Current | 1.4μA |
| Slew Rate | 0.001V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 25pA |
| Voltage - Supply, Single/Dual (±) | 2.2V~36V ±1.1V~18V |
| Output Current per Channel | 1.5mA |
| Input Offset Voltage (Vos) | 150μV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 2.7 kHz |
| Voltage Gain | 113.98dB |
| Average Bias Current-Max (IIB) | 0.01μA |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.36μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 2.7 kHz |
| Wideband | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1495HS8#PBF Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. There are two types of operational amplifiers in this circuit. In the case of Tube cases, linear amplifier will be delivered. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 15V volts. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are included on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 150μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureAs long as the supply current of the chip does not exceed 1.4μA, this op amp ic can operate. It is recommended to keep the voltage gain at 113.98dB at all times. This op amp ic has 2 circuits. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. This linear amplifier has a total of 2 elements. Buffer op amp series numbers are indicated by the Over-The-Top?.
LT1495HS8#PBF Features
8 Pins
supply voltage of 15V
113.98dB voltage gain
Output Type: Rail-to-Rail
LT1495HS8#PBF Applications
There are a lot of Linear Technology/Analog Devices LT1495HS8#PBF Instrumentational OP Amps applications.
- earphone
- Hand-held batteries
- Large motor controllers
- High input resistance broadband
- Portable electronic products powered by batteries
- Automation control systems
- E-book readers
- Broadcasting
- Non-polarized electrodes
- Video amplifiers
