LT1784CS5#TRMPBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| Published | 2009 |
| Series | Over-The-Top® |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 250 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LT1784 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Operating Supply Current | 750μA |
| Slew Rate | 2.2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 250nA |
| Voltage - Supply, Single/Dual (±) | 2.5V~18V ±1.25V~9V |
| Output Current per Channel | 27mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Gain Bandwidth Product | 2.6MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 2600 kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 9V |
| Voltage - Input Offset | 1.6mV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Nominal Gain Bandwidth Product | 2.5MHz |
| Wideband | NO |
| Height | 900μm |
| Length | 2.9mm |
| Width | 1.75mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1784CS5#TRMPBF Overview
A SOT-23-5 Thin, TSOT-23-5 case is used to package the op amp. A General Purpose-type buffer amplifier is shown here. The op amp is delivered to you in a Cut Tape (CT) case. There have been a total of 5 terminations over the past year. In total, there are 5 pins on this op amp ic. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. Linear amplifier includes 5 pins. With regard to input offset voltage, instrumentation amplifier is rated at 3.5mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. The buffer amplifier is capable of operating from a supply current of 750μA . Op amp is a member of the 120dB's 120dB family. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. There are a total of 1 elements in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 5V. TAPE AND REEL is adopted to pack the instrumentation amplifier. In this case, Over-The-Top? represents the instrumentation amplifiers' series number.
LT1784CS5#TRMPBF Features
5 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
LT1784CS5#TRMPBF Applications
There are a lot of Linear Technology/Analog Devices LT1784CS5#TRMPBF Instrumentational OP Amps applications.
- Video computer boards
- Weak signal detection
- Inverse/same-phase proportional circuit
- Ultrasound transducers
- Signal amplification
- Power generator
- Logarithmic operation circuits
- Car stereo
- High-frequency data acquisition systems
- Gaming industry
