LTC3835EDHC-1#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC3835 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 10V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 20A |
| Voltage - Supply (Vcc/Vdd) | 4V~36V |
| Control Features | Enable, Soft Start, Tracking |
| Input Voltage (Min) | 4V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 250kHz~530kHz |
| Input Voltage (Max) | 36V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 580kHz |
| Duty Cycle (Max) | 99.4% |
| Clock Sync | No |
| Height Seated (Max) | 0.8mm |
| Length | 5mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
LTC3835EDHC-1#PBF Overview
It comes in the 16-WFDFN Exposed Pad package, which makes switching controller suitable for most applications. This dc motor controller can be used to generate outputs with 1 numbers. There is a Tube solid enclosure around the pmic. There are Transistor Driver dc switching's output (s) that it can handle. dc control's supply and operating voltages are 4V~36V. Qualified to work in an dc switcher with -40°C~85°C TA. The switching controller can be switched at 250kHz~530kHz. Surface Mount makes it suitable for general dc dc regulator. Featured in the dcdc regulator is Enable, Soft Start, Tracking which allows efficient switching control. SWITCHING CONTROLLER analog IC connects the switch converters. DUAL are the position of the terminal of the switching converters. 16 terminations with a variety of function. To name a few of the control techniques these dc dc converter ics adapt, it includes PULSE WIDTH MODULATION. The DC switcher's nominal voltage is 12V. Other relevant dc to dc converter ics can be found by searching "LTC3835". There are only 16 pins on switching converter. The type is a particular Switching Regulator or Controllers of switching converter. This dc dc voltage regulator should be powered by a voltage of 4V. DC regulator outputs 10V voltage based on test statistics. A maximum voltage of 36V is accepted by the dc to dc regulator as an input voltage. If you start a project, note down the dc dc regulator's usual output current of 20A. There is a maximum frequency of 580kHz on this dc regulators.
LTC3835EDHC-1#PBF Features
Transistor Driver Outputs
Switching Frequency: 250kHz~530kHz
Enable, Soft Start, Tracking
PULSE WIDTH MODULATION
LTC3835EDHC-1#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC3835EDHC-1#PBF DC to DC converter applications.
- Network technology
- Lathes
- Communication system
- Domestic water pumps
- Production lines
- Hydraulic presses
- Overvoltage protection circuits in TV sets
- Telecommunications equipment
- Geothermal power
- Radio equipment
