LV8014T-MPB-E
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-TFSOP (0.173, 4.40mm Width) |
| Number of Pins | 24 |
| Operating Temperature | -20°C~75°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e6 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 24 |
| Terminal Finish | Tin/Bismuth (Sn/Bi) |
| Applications | DC Motors, General Purpose |
| Additional Feature | ALSO OPERATES IN 2 TO 7V |
| HTS Code | 8542.39.00.01 |
| Subcategory | Motion Control Electronics |
| Technology | DMOS |
| Voltage - Supply | 2.7V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 24 |
| Qualification Status | Not Qualified |
| Max Output Current | 2.5A |
| Operating Supply Voltage | 7V |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Interface | Logic |
| Analog IC - Other Type | AC MOTOR CONTROLLER |
| Nominal Supply Current | 1μA |
| Output Configuration | Half Bridge (4) |
| Power Dissipation | 800mW |
| Output Current | 1.4A |
| Output Current per Channel | 1.4A |
| Supply Current-Max (Isup) | 1.2mA |
| Voltage - Load | 2V~7V |
| Fault Protection | Over Temperature |
| Rds On (Typ) | 750m Ω |
| Load Type | Inductive |
| Height Seated (Max) | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
LV8014T-MPB-E Overview
For packaging, it is used with Tube.Cost savings are achieved by including H bridge in the 24-TFSOP (0.173, 4.40mm Width) package.Improved reliabilbridge drivery can be ensured based on the supply voltage of 2.7V~5.5V.H bridge circuit is mounted in the way of Surface Mount.Motor driver H bridge is possible for -20°C~75°C TA to operate normally at motor driver H bridges operating temperature.Among H bridge motor drivers many applications are DC Motors, General Purpose.Mount the board using Surface Mount.There are 24 terminations used to end a transmission line with the H bridge that matches the characteristic impedance of the line.A signal interface uses 24 pins as pronged contacts.For the operation of the H bridge, a voltage supply of 5V is used.This H bridge circuit incorporates an analog IC with the type AC MOTOR CONTROLLER.An ambient temperature of 2.5A determines the maximum load current that a power supply can deliver.Currently, 1.4A current flows through the output and power supply pins.It is the 24 pins that enable this bridge driver to perform its specific functions.This H bridge motor driver belongs to the subcategory of Motion Control Electronics and shares several similarities with other parts in that category.For the highest level of efficiency, the operating supply voltage is kept at 7V.A load of electricity is supplied by 5V.H-bridge is also able to provide ALSO OPERATES IN 2 TO 7V.
LV8014T-MPB-E Features
Available in 24-TFSOP (0.173, 4.40mm Width) Package / Case
Operating Temperature at the range of Surface Mount
Number of Receivers: 7V
With ALSO OPERATES IN 2 TO 7V Drivers
LV8014T-MPB-E Applications
There are a lot of ON Semiconductor LV8014T-MPB-E Full Bridge Drivers, Half-Bridge Drivers applications.
- Optical disc drives
- Voltage Regulators
- Workstations
- Industrial Pumps
- DC-DC Converters
- High-Current DC-DC Point-of-Load Converters
- Audio-visual equipment
- Desktop Computers
- Telecom Microprocessor
- OA equipments
