Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 4 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-UFDFN Exposed Pad |
Number of Pins |
10 |
Operating Temperature |
-30°C~150°C TJ |
Packaging |
Tape & Reel (TR) |
Published |
2012 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
Terminal Finish |
Tin (Sn) |
Applications |
DC Motors, General Purpose |
HTS Code |
8542.39.00.01 |
Subcategory |
Motion Control Electronics |
Technology |
Bi-CMOS |
Voltage - Supply |
2V~6V |
Terminal Position |
DUAL |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Pin Count |
10 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
5V |
Supply Voltage-Max (Vsup) |
6V |
Power Supplies |
5V |
Supply Voltage-Min (Vsup) |
2V |
Interface |
PWM |
Analog IC - Other Type |
BRUSH DC MOTOR CONTROLLER |
Nominal Supply Current |
1.6mA |
Power Dissipation |
1.05kW |
Output Current-Max |
0.7A |
Halogen Free |
Halogen Free |
Output Current per Channel |
700mA |
Collector Emitter Voltage (VCEO) |
6V |
Max Collector Current |
700mA |
Voltage - Load |
2V~6V |
Fault Protection |
Over Temperature |
Switching Frequency |
60kHz |
Motor Type |
Brushless DC (BLDC) |
Load Type |
Inductive |
Height |
500μm |
Length |
2.6mm |
Width |
2.6mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
LV8163QA-BH Overview
In this package, Tape & Reel (TR) is used.For cost-saving purposes, H bridge is included in the 10-UFDFN Exposed Pad package.Bridge driver is possible to ensure improved reliabilbridge drivery by varying the supply voltage of 2V~6V.H bridge circuit is mounted on Surface Mount.-30°C~150°C TJ can work normally at motor driver H bridges operating temperature.There are a variety of applications for H bridge motor driver, including DC Motors, General Purpose.PCB mounting is performed using Surface Mount.Transmission lines are terminated with H bridges whose characteristic impedance matches their characteristic impedance, known as 10 terminations.In signal interfaces, 10 pins serve as pronged contacts.For the operation of the H bridge, a voltage supply of 5V is used.The analog IC type is BRUSH DC MOTOR CONTROLLER.It is made up of two 10 pins that work together to perform the specific functions of this bridge driver.This H bridge motor driver falls under the subcategory of Motion Control Electronics.To ensure high efficiency, the operating supply voltage is maintained at 5V.5V supplies electricity to the electrical load.
LV8163QA-BH Features
Available in 10-UFDFN Exposed Pad Package / Case
Operating Temperature at the range of Surface Mount
Number of Receivers: 5V
LV8163QA-BH Applications
There are a lot of ON Semiconductor LV8163QA-BH Full Bridge Drivers, Half-Bridge Drivers applications.
- VTR
- Small Form-Factor Voltage Regulator Modules
- Dual DC motor
- PC peripherals
- Networking Microprocessor Voltage Regulators
- Optical disc drives
- DC-DC Converters
- High current, low profile DC-DC converters
- Audio-visual equipment
- Industrial Fans