MAX16930ATLR/V+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 40-WFQFN Exposed Pad |
| Number of Pins | 40 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| Published | 2016 |
| Series | Automotive, AEC-Q100 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 40 |
| ECCN Code | EAR99 |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | QUAD |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX16930 |
| Function | Step-Up, Step-Down |
| Number of Outputs | 3 |
| Output Voltage | 10V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 36V |
| Input Voltage-Nom | 14V |
| Analog IC - Other Type | DUAL SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 6A |
| Voltage - Supply (Vcc/Vdd) | 3.5V~42V |
| Control Features | Enable, Frequency Control, Power Good |
| Topology | Buck, Boost |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 1MHz~2.2MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Duty Cycle (Max) | 95% |
| Output Phases | 2 |
| Height Seated (Max) | 0.8mm |
| Length | 6mm |
| Width | 6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX16930ATLR/V+ Overview
It comes in a 40-WFQFN Exposed Pad package, so switching controller can be used for most applications. For 3 outputs, the dc motor controller is appropriate. The pmic is packaged in Tube solid enclosure. With Transistor Driver dc switching's output (s), it is able to handle it. dc control's supply and operating voltages are 3.5V~42V. Qualified to work in an dc switcher with -40°C~125°C TJ. With this switching controller, you can switch at 1MHz~2.2MHz. dc dc regulators can be carried out with Surface Mount. In order to control switching efficiently, the dcdc regulator features Enable, Frequency Control, Power Good. An analog IC with the DUAL SWITCHING CONTROLLER signal is connected to the switch converters. switching converters terminal (s) are designed to be at QUAD. 40 terminations with a variety of function. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. DC switcher's input voltageis 14V volts. Searching "MAX16930" will return other relevant dc to dc converter ics. There are a total of 40 pins on switching converter. Switching converter is a type of Switching Regulator or Controllers in particular. The test statistics indicate that DC regulator outputs a voltage of 10V. A starting point for a project is to note down the dc dc regulator's usual output current, which is 6A. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. It is suggested that users apply 36V to the voltage regulator dc to dc in order to run it safely and reliably in a circuit. The dc to dc voltage regulator is from the Automotive, AEC-Q100 series.
MAX16930ATLR/V+ Features
Transistor Driver Outputs
Switching Frequency: 1MHz~2.2MHz
Enable, Frequency Control, Power Good
PULSE WIDTH MODULATION
MAX16930ATLR/V+ Applications
There are a lot of Maxim Integrated MAX16930ATLR/V+ DC to DC converter applications.
- Direct power supply system
- Scientific research
- Medical monitoring systems
- Wide-range voltage regulation circuits
- Electrical distribution systems
- Handheld GPS
- Motor controller circuits
- Digital display device
- Milling machines
- PSRR circuits
