MAX231EPD+
| Parameters | |
|---|---|
| Interface | RS-232 |
| Number of I/O | 8 |
| Nominal Supply Current | 1mA |
| Propagation Delay | 10 μs |
| Logic Function | Receiver, Transceiver |
| Data Rate | 120Kbps |
| Output Characteristics | TOTEM-POLE |
| Differential Output | NO |
| Output Polarity | INVERTED |
| Protocol | RS232 |
| Input Characteristics | SCHMITT TRIGGER |
| Number of Drivers/Receivers | 2/2 |
| Receiver Number of Bits | 2 |
| Duplex | Full |
| Receiver Hysteresis | 500mV |
| Number of Drivers | 2 |
| Number of Transceivers | 1 |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | EXTERNAL CHARGE PUMP |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 5V 7.5V~13.2V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX231 |
| Pin Count | 14 |
MAX231EPD+ Overview
LED drivers benefit from this IC's enhanced 14-DIP (0.300, 7.62mm) package.The receiver is packaged in a Tube package.It has proved to be a valuable component for a variety of applications since it is a Transceiver can transceiver.Ideally, you should place this wide receiver on a Through Hole-type PCB or development board.This differential driver uses 5V 7.5V~13.2V for power supply.This electronic part can have?up to 2/2 eligible receivers/drivers on the field at once.?IC receiver is designed for applications with a temperature of -40°C~85°C.An output voltage range of 5V is sufficient to run this line driver ic efficiently.The integrated terminations of this wide receiver allow it to drive and receive signals from data.Transceiver comes with 14 standard pinouts that meet the market's requirements.The base part number MAX231 identifies the product type, temperature, package, etc., so you can search for more variants by using it.This is a 14-pin driver IC with enhanced power dissipation control.Package size is drastically reduced by downsizing ICs and mounting them in high-density Through Hole arrays.As a general rule, this receiver has a resolution of 2 bits that is usually specified.A subcategory named Line Driver or Receivers can be used to group this rf transceiver module.There are 1 transceivers in total that this module isolated transceiver implements.On the part, 2 drivers are embedded in order to facilitate the operation of the device.With the EXTERNAL CHARGE PUMP function, this optical transceiver module improves accuracy and stability of signal management overall.It is an integrated circuit with 8 serial I/Os that are in line with industry standards.
MAX231EPD+ Features
Tube package
14 pin count
14 pins
MAX231EPD+ Applications
There are a lot of Maxim Integrated MAX231EPD+ Drivers/Receivers/Transceivers applications.
- Routers
- Wireless security systems
- Cordless telephone
- Low power, low voltage systems
- Clock radio
- VoIP phones
- SONET/SDH Network
- Structural bonding
- Copper connection network
- IP cameras
