MAX3086ESD+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX3086 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Nominal Supply Current | 600μA |
| Data Rate | 10Mbps |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 100mV |
| Number of Transceivers | 1 |
| ESD Protection | No |
| Simplex/Duplex | Full Duplex |
| Transmit Delay-Max | 60 ns |
| Output Low Current-Max | 0.004A |
| Out Swing-Min | 2 V |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX3086ESD+ Overview
LED drivers with the enhanced 14-SOIC (0.154, 3.90mm Width) package will be able to drive a variety of common LEDs with ease.The receiver is packaged in a Tube package.Several solutions have used this Transceiver can transceiver in a variety of applications due to its Transceiver IC nature.This wide receiver can be placed on any Surface Mount-type PCB or development board.Power supply requirements for this differential driver are 4.75V~5.25V.Up to 1/1 receivers/drivers can be installed simultaneously on this electronic part.IC receiver likes this one are designed for use in applications where operating temperatures are -40°C~85°C.Driver ICs in this category can operate efficiently with a supply voltage range of 5V.This wide receiver has 14 terminations for driving and receiving data signals.The transceiver is packaged with 14 market standard pinouts so that it can be easily used.Since the base part number MAX3086 describes the product type, temperature, package, etc., you might get more options by searching with it.The driver IC has improved power dissipation control.As a result of optical transceiver downsizing and high-density Surface Mount mounting technologies, its package size has been greatly reduced.As a result of the ic receiver, the resolution of the driver was increased to 1 bits.It is typical for this receiver to have a resolution of 1 bits when it is specified.As a result of the design of this transceiver module, the input voltage supply is designed to operate at 5V.3 volts.There is a subcategory called Line Driver or Receivers for this rf transceiver module.IC5V is a high performance driver IC designed to work with a 5V power supply.This IC implements 1 transceivers overall.
MAX3086ESD+ Features
Tube package
14 pin count
14 pins
5V power supply
MAX3086ESD+ Applications
There are a lot of Maxim Integrated MAX3086ESD+ Drivers/Receivers/Transceivers applications.
- Satellite radio receiver
- Fiber optic cable connection network
- Datacom networking applications
- Remote controls
- Wireless security systems
- Long-distance fiber optic network applications
- Shortwave receiver
- Metro access rings
- Wireless communication
- Car alarm systems
