Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
1998 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
60Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
727mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX323 |
Output |
SEPARATE OUTPUT |
Pin Count |
8 |
Power Supplies |
3.3/5V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1μA |
Nominal Supply Current |
100pA |
Max Supply Current |
100pA |
Throw Configuration |
SPST |
Turn On Delay Time |
150 ns |
Supply Type |
Single |
Turn-Off Delay Time |
100 ns |
On-State Resistance (Max) |
60Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
0.8Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
150ns, 100ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
800m Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
2.7V~16V |
Normal Position |
NO |
Height Seated (Max) |
1.75mm |
Length |
4.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX323ESA+T Overview
Presented in 8-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. A total of 8 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. Electronic part bodies are injected with 8 pins. A SPST - NO switching circuit is used for these analog switches. There are 2 circuits in this switch device. Try searching for the analog switch ic with MAX323 if you are looking for variants. The internal resistance of this digital multiplexer is 60Ohm. Datasheets for 8 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 16V to a switch device. Analogue multiplexer with a Single supply type that is cost-effective. 2.7V is the lowest voltage the electrical component should receive. An operating current of 1μA would be sufficient for this switch device. Using a single voltage supply, this switch device consumes 2.7V~16V volts. If you put voltage higher than 100pA on the digital multiplexer, damage may occur. This analog switch ic utilizes SEPARATE OUTPUT output.
MAX323ESA+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX323ESA+T Applications
There are a lot of Maxim Integrated MAX323ESA+T Analog Switches & Multiplexers ICs applications.
- Channel Banks
- Wireless Local Loop
- Avionics and Military Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Medical Instrumentation
- SONET/SDH ADM
- Remote wireless modules
- Channelized and Unchannelized DS3 applications
- PBXs
- Routers