MAX329CWE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 3.5kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 750mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX329 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 4.5μA |
| Throw Configuration | 4PST |
| Propagation Delay | 1.5 μs |
| Turn On Delay Time | 1.5 μs |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±5V~18V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 1 μs |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 3.5kOhm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 84 dB |
| Current - Leakage (IS(off)) (Max) | 10pA |
| Channel Capacitance (CS(off), CD(off)) | 1.8pF 8pF |
| On-state Resistance Match-Nom | 30Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 1.5μs, 1μs |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 70 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1500ns |
| Switch-off Time-Max | 1000ns |
| Signal Current-Max | 0.01A |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX329CWE+T Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.295, 7.50mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 4:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. The total number of terminations is 16. This electronic part offers high-quality output due to its 4 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 16 pins. Unlike digital switches, these are based on SP4T switching circuits. The multiplexer consists of 2 circuits. Look for analog switch ic variants by searching with MAX329. It has an internal resistance of 3.5kOhm. Datasheets for functions of 16 pins are available. Users should never supply a voltage higher than 30V to a switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 10V is the lowest voltage the electrical component should receive. 4.5μA current would be enough for this multiplexer to operate. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. When using dual power supplies, you should attach at least 5V. Operating voltages of 28V are compatible with the electrical part.
MAX329CWE+T Features
4 Channels
Switch Circuit: SP4T
4.5μA Supply Current
MAX329CWE+T Applications
There are a lot of Maxim Integrated MAX329CWE+T Analog Switches & Multiplexers ICs applications.
- High reliability control systems
- E1 Network Equipment
- SONET
- PDH Multiplexers
- Remote Powered Equipment
- SONET/SDH ADM
- Audio and video signal routing
- Remote wireless modules
- Precision test equipment
- Existing multiplexer applications (both fault-protected and nonfault-protected)
