banner_page

MAX333ACAP

175ns, 145ns SPDT 45Ohm Analog Switches MAX333 20 Pins 250pA 15V 20-SSOP (0.209, 5.30mm Width)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX333ACAP
  • Package: 20-SSOP (0.209, 5.30mm Width)
  • Datasheet: PDF
  • Stock: 349
  • Description: 175ns, 145ns SPDT 45Ohm Analog Switches MAX333 20 Pins 250pA 15V 20-SSOP (0.209, 5.30mm Width)(Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 20-SSOP (0.209, 5.30mm Width)
Number of Pins 20
Operating Temperature 0°C~70°C TA
Packaging Tube
Published 1999
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 20
ECCN Code EAR99
Resistance 35Ohm
Terminal Finish Tin/Lead (Sn85Pb15)
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 240
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 0.65mm
Time@Peak Reflow Temperature-Max (s) 20
Base Part Number MAX333
Pin Count 20
Operating Supply Voltage 20V
Number of Channels 4
Max Supply Voltage 30V
Min Supply Voltage 10V
Operating Supply Current 1μA
Nominal Supply Current 50μA
Max Supply Current 50μA
Turn On Delay Time 175 ns
Voltage - Supply, Single/Dual (±) 10V~30V ±4.5V~20V
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 145 ns
Max Dual Supply Voltage 20V
On-State Resistance (Max) 45Ohm
Min Dual Supply Voltage 4.5V
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 72 dB
Current - Leakage (IS(off)) (Max) 250pA
Channel Capacitance (CS(off), CD(off)) 5pF
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 175ns, 145ns
Charge Injection 2pC
Channel-to-Channel Matching (ΔRon) 2 Ω (Max)
Crosstalk -78dB @ 1MHz
Height Seated (Max) 1.99mm
Length 7.2mm
Width 5.29mm
Radiation Hardening No
REACH SVHC Unknown
RoHS Status Non-RoHS Compliant
Lead Free Contains Lead

MAX333ACAP Overview


Due to its 20-SSOP (0.209, 5.30mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. The multiplexer is located in Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around 0°C~70°C TA. There are 20 terminations totally. As a result of its 4 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. This electronic part can be found in the 20 series. Based on SPDT switching circuits, these analog multiplexers work. Look for analog switch ic variants by searching with MAX333. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. For details about the functions of 20 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended to use 10V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1μA current. Putting voltage greater than 50μA on the multiplexer may cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. When using dual power supplies, you should attach at least 4.5V. The electrical part can be operated at 20V voltage levels.

MAX333ACAP Features


4 Channels
Switch Circuit: SPDT
1μA Supply Current

MAX333ACAP Applications


There are a lot of Maxim Integrated MAX333ACAP Analog Switches & Multiplexers ICs applications.

  • Channel Banks
  • Mechanical reed relay replacement
  • Data Acquisition Systems
  • Medical
  • Multiplexers
  • Microprocessor Controlled Analog Systems
  • PBXs
  • Industrial
  • ATM
  • Modems

Write a review

Note: HTML is not translated!
    Bad           Good