MAX382CWN+T
| Parameters | |
|---|---|
| Number of Terminations | 18 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX382 |
| Pin Count | 18 |
| Operating Supply Voltage | 12V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 2.4V |
| Operating Supply Current | 1μA |
| Propagation Delay | 275 ns |
| Turn On Delay Time | 500 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2.7V~16.5V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 2.4V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 200pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 18-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
MAX382CWN+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 18-SOIC (0.295, 7.50mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 8:1. Operating temperature extended to 0°C~70°C TA. In total, there are 18 terminations. Due to its 8 channels, the electrical component produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. There is an electrical component included in the 18 series. There are 1 circuits in this switch device. Try searching for the analog switch ic with MAX382 if you are looking for variants. A 100Ohm internal resistance characterizes this multiplexer. In normalcircumstances, users should not exceed 15V volts for the multiplexer. An effective Dual, Single supply digital multiplexer. A low voltage of 2.4V should be applied to the electronic component. This multiplexer would work with 1μA current. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 8V. It is recommended that you attach at least 2.4V to your dual power supply. Operating voltages of 12V are compatible with the electrical part.
MAX382CWN+T Features
8 Channels
1μA Supply Current
MAX382CWN+T Applications
There are a lot of Maxim Integrated MAX382CWN+T Analog Switches & Multiplexers ICs applications.
- New designs requiring multiplexer functions
- Cross Connects
- Avionics
- Modems
- PBXs
- ATM
- Fault Tolerant Systems
- Mechanical reed relay replacement
- Audio and video switching
- Fiber to the Home
