MAX394EPP
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | MAX394 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Operating Supply Voltage | 8V |
| Power Supplies | 3.3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 100nA |
| Nominal Supply Current | 60nA |
| Max Supply Current | 60nA |
| Turn On Delay Time | 130 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~15V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 2.4V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 66 dB |
| Current - Leakage (IS(off)) (Max) | 200pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Length | 26.16mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX394EPP Overview
The electronic part can be shipped overseas conveniently because it is packaged in 20-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. Through Hole is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 2:1. Temperatures around -40°C~85°C TA are extended for operation. Totally, there are 20 terminations. This electronic part offers high-quality output due to its 1 channels. With a 5V voltage supply, the electrical component should be turned on and run. A key feature of the 20 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPDT switching circuits. 4 circuits are used in this analogue multiplexer. If you are looking for variants of the digital switch, trying search with MAX394. This digital multiplexer has 35Ohm internal resistance. To find out what the functions of 20 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 16V should not normally be supplied to the switches. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 2.7V. This digital switch can be operated with a current of 100nA. When the digital multiplexer is charged above 60nA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 8V. For dual power supplies, a voltage of at least 2.4V should be attached. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. 8V operating voltages are supported by the electronic component.
MAX394EPP Features
1 Channels
Switch Circuit: SPDT
100nA Supply Current
MAX394EPP Applications
There are a lot of Maxim Integrated MAX394EPP Analog Switches & Multiplexers ICs applications.
- Central office
- Video switching
- Communications systems
- Cross Connects
- Avionics
- PBX interfaces
- Precision instrumentation
- Industrial control systems
- Audio and video switching
- SONET/SDH ADM
