MAX395CAG+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 24 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 175Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 1W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 8 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX395 |
| Pin Count | 24 |
| Operating Supply Voltage | 8V |
| Number of Channels | 1 |
| Number of Circuits | 8 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 7μA |
| Nominal Supply Current | 30μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 500 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 2pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 400ns, 400ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω (Max) |
| Crosstalk | -90dB @ 100kHz |
| Switch-on Time-Max | 400ns |
| Switch-off Time-Max | 400ns |
| Height Seated (Max) | 1.99mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX395CAG+ Overview
As the electronic part is packed in 24-SSOP (0.209, 5.30mm Width), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tube. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Increasing operating temperature to around 0°C~70°C TA. Total terminations are 24. High-quality output is provided by the electronic component's 1 channels. With a 5V voltage supply, the electrical component should be turned on and run. The electronic part body is injected with 24 pins. These analog multiplexers are built based on SPST - NO switching circuits. The multiplexer consists of 8 circuits. If you are looking for variants of the digital switch, trying search with MAX395. Analog switches have 175Ohm internal resistance. Datasheets for functions of 24 pins are available. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 2.7V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 7μA current. If put voltage greater than 20μA on the device, damage may be caused to the analogue multiplexer. If put voltage greater than 8V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 3V. Operating voltages of 8V are compatible with the electrical part.
MAX395CAG+ Features
1 Channels
Switch Circuit: SPST - NO
7μA Supply Current
MAX395CAG+ Applications
There are a lot of Maxim Integrated MAX395CAG+ Analog Switches & Multiplexers ICs applications.
- Audio/video switches
- Medical Instrumentation
- Cross Connects
- Remote wireless modules
- Optical Applications
- Transmit
- Sample hold systems
- ISDN NT1/TA
- Industrial and process control systems
- Channelized and Unchannelized DS3 applications
