MAX398CSE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX398 |
| Pin Count | 16 |
| Operating Supply Voltage | 12V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 1μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 500 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 6 Ω (Max) |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX398CSE+T Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 8:1 represents the number of circuits. Increasing operating temperature to around 0°C~70°C TA. 16 terminations have been made so far. The electronic part provides high-quality output because it has 8 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. The circuits in this analogue multiplexer number 1. Try searching with MAX398 if you're looking for variants. There is 100Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 15V. A low voltage of 3V should be applied to the electronic component. 1μA current would be enough for this multiplexer to operate. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 8V. For dual power supplies, a voltage of at least 3V should be attached. It is integrated with a SINGLE-ENDED MULTIPLEXER analog IC. The electronic component can function from 12V.
MAX398CSE+T Features
8 Channels
1μA Supply Current
MAX398CSE+T Applications
There are a lot of Maxim Integrated MAX398CSE+T Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- Battery Powered Instruments
- DVD-R
- PDH Multiplexers
- RGB switches
- Automatic test equipment
- Voice over IP/DSL – Integrated Access Devices, Smart
- Digital cross connects (DSX-1)
- High speed data transmission line cards
- PBXs
