MAX4231AYT+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 6-UFLGA |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 170.2mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4231 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Operating Supply Current | 1.2mA |
| Nominal Supply Current | 1.1mA |
| Output Current | 200mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 52 dB |
| Current - Input Bias | 50pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.5V |
| Output Current per Channel | 200mA |
| Input Offset Voltage (Vos) | 850μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.00055μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height Seated (Max) | 0.55mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4231AYT+T Overview
A 6-UFLGA case is used to package the op amp. There are two types of operational amplifiers in this circuit. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. There have been a total of 6 terminations over the past year. It consists of a total of 6 pins in total. This linear amplifier should be powered by an 2.7V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. Linear amplifier includes 6 pins. There is an input offset voltage of 850μV for this buffer op amp. Surface Mount is the recommended mounting type for this linear amplifier. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureAn 1.2mA volt supply current is needed for this linear amplifier to operate. You should keep the voltage gain at 100dB for the time being. There are 1 circuits on op amps. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted.
MAX4231AYT+T Features
6 Pins
supply voltage of 2.7V
100dB voltage gain
Output Type: Rail-to-Rail
MAX4231AYT+T Applications
There are a lot of Maxim Integrated MAX4231AYT+T Instrumentational OP Amps applications.
- Car stereo
- Vehicle electronics
- Polarized electrodes
- Power control
- Comparator
- Signal operation
- Portable electronic products powered by batteries
- Video amplifiers
- Micro signal measurement
- Video data acquisition
