MAX4544EUT+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4544 |
| Pin Count | 6 |
| Output Type | Fixed |
| Polarity | Non-Inverting |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Number of Bits | 2 |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| On-State Resistance (Max) | 60Ohm |
| High Level Output Current | 10mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Drain to Source Resistance | 60Ohm |
| On-State Resistance | 30Ohm |
| Height | 1.45mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4544EUT+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOT-23-6. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature extended to -40°C~85°C TA. The total number of terminations is 6. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. There is an electrical component included in the 6 series. A SPDT switching circuit is used for these analog switches. A 1 circuit is present in this switch device. Try searching for MAX4544 variants of the analog switch ic. Analog switches have 60Ohm internal resistance. Please refer to the datasheets for 6 pins functions. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 12V voltage to the switch device. An effective Single supply digital multiplexer. 2.7V is the lowest voltage the electrical component should receive. Using a single voltage supply, this switch device consumes 2.7V~12V volts. When the digital multiplexer is charged above 1μA, damage can occur. There is 60Ohm resistance between Drain and Source for this electronic part. It is capable of carrying out 2-bit operation.
MAX4544EUT+T Features
1 Channels
Switch Circuit: SPDT
Drain-to-Source resistance: 60Ohm
2-Bit
MAX4544EUT+T Applications
There are a lot of Maxim Integrated MAX4544EUT+T Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Remote wireless modules
- Audio and video routing
- Relay Replacement
- Industrial
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery Powered Systems
- Central office
- PBX interfaces
