MAX4608EPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 2.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4608 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 64pF 64pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 110ns, 150ns |
| Charge Injection | 45pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -66dB @ 1MHz |
| Normal Position | NO |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4608EPE Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tube is used. This analog switch is mounted in Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. As a result of its 1 channels, this electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. There are 16 pins injected into the electronic part body. Multiplexers built on a SPST - NO switching circuit are built. 2 circuits are used in this analogue multiplexer. Try searching for MAX4608 variants of the analog switch ic. As far as internal resistance is concerned, it has 2.5Ohm. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. A low voltage of 4.5V should be applied to the electronic component. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX4608EPE Features
1 Channels
Switch Circuit: SPST - NO
MAX4608EPE Applications
There are a lot of Maxim Integrated MAX4608EPE Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- DVD-R
- Data Acquisition Systems
- Communication systems
- Video signal routing
- Multiplexers
- FTTH
- Sample hold systems
- PCMCIA cards
- Data switching
