MAX4632EPE
| Parameters | |
|---|---|
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -66dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 500ns |
| Switch-off Time-Max | 400ns |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4632 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 18pF 18pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 5pC |
MAX4632EPE Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tube. Multiplexers like this are mounted in the Through Hole position. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature extended to -40°C~85°C TA. In total, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. An electrical component like this is included in the 16 series. Based on SPDT switching circuits, these analog multiplexers work. A 2 circuit is present in this switch device. Try searching with MAX4632 to find analog multiplexer variants. It has an internal resistance of 85Ohm. You can find the functions of the 16 pins in the datasheets. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 36V to a switch device. 9V is the lowest voltage the electrical component should receive. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. The voltage should be at least 4.5V if you are using dual power supplies. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX4632EPE Features
1 Channels
Switch Circuit: SPDT
MAX4632EPE Applications
There are a lot of Maxim Integrated MAX4632EPE Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- Imaging
- Automatic test equipment
- CSU
- Relay Replacement
- Medical
- Video signal routing
- High reliability control systems
- Avionics test equipment
- Medical systems
