MAX4660ESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) Exposed Pad |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 25Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.509W |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MAX4660 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 200μA |
| Max Supply Current | 200μA |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| -3db Bandwidth | 225MHz |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 1.5pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -76dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4660ESA+T Overview
The electronic component is convenient to ship overseas because it is packed in a 8-SOIC (0.154, 3.90mm Width) Exposed Pad. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 2:1. Operating temperature extended to -40°C~85°C TA. The total number of terminations is 8. The electronic part provides high-quality output because it has 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. Electronic part bodies are injected with 8 pins. Multiplexers built on a SPDT switching circuit are built. There are 1 circuits in this multiplexer. Look for analog switch ic variants by searching with MAX4660. Internally, this switch multiplexer has a resistance of 25Ohm. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 40V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 9V is the lowest voltage the electrical component should receive. A voltage higher than 200μA may cause damage to the switch multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 20V. With dual power supplies, you should attach at least 4.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. There is a voltage range of 20V operating voltages for the electrical part.
MAX4660ESA+T Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 225MHz
MAX4660ESA+T Applications
There are a lot of Maxim Integrated MAX4660ESA+T Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- High reliability control systems
- Audio/video switches
- FTTH
- Intelligent PBX
- Cross Connects
- Fault Tolerant Systems
- DVD-R
- Cell phones
- Data Acquisition Systems
