MAX487ECSA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX487 |
| Pin Count | 8 |
| Output Voltage | 3V |
| Max Output Current | 250mA |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Operating Supply Current | 250μA |
| Nominal Supply Current | 300μA |
| Propagation Delay | 250 ns |
| Data Rate | 250kbps |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 70mV |
| Number of Transceivers | 1 |
| ESD Protection | Yes |
| Receive Delay-Max | 2000 ns |
| Simplex/Duplex | Half Duplex |
| Transmit Delay-Max | 2000 ns |
| High Level Input Current-Max | 0.00025A |
| Height | 1.75mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX487ECSA+ Overview
Driver ICs with enhanced 8-SOIC (0.154, 3.90mm Width) packages are excellent for driving LEDs with common characteristics.The Tube package contains this receiver.The Transceiver can transceiver type enables this part to be used in a wide range of applications.You can place this wide receiver to any Surface Mount-type PCB or development board.It takes 4.75V~5.25V from the power supply to run this differential driver.There can be up to 1/1 eligible receivers/drivers on the field at the same time with this electronic part.IC receiver has been designed primarily for applications operating at 0°C~70°C.Driver ICs with a supply voltage range of 5V can operate efficiently.In order to drive and receive signals from data, this wide receiver has 8 terminations integrated.The pinouts for this transceiver are standardized to meet the needs of the market.You can search with MAX487 to get more variants of this part, since it identifies the product type, temperature, package, etc.The driver IC has improved power dissipation control.This package size decreases dramatically due to optical transceiver downsizing and high-density Surface Mount mounting technologies.Using this ic receiver, you were able to achieve a resolution of 1 bits.In most cases, the receiver will be specified with a 1-bit resolution.As a result of the design of this transceiver module, the input voltage supply is designed to operate at 5V.3 volts.It is possible to subcategoriLine Driver or Receiverse this rf transceiver module as Line Driver or Receivers.Driver ICs are designed to work with a 5V power supply and this driver IC is one of them.There are 1 transceivers in total implemented by this IC.With this integrating circuit you can drive LEDs of a voltage of up to 250μA. It can be used to drive large displays.Voltage can be delivered at 3V by Wide receiver.
MAX487ECSA+ Features
Tube package
8 pin count
8 pins
5V power supply
MAX487ECSA+ Applications
There are a lot of Maxim Integrated MAX487ECSA+ Drivers/Receivers/Transceivers applications.
- WDM transmission
- transmission relay
- Remote controls
- Clock radio
- Desktop PC
- Wireless 3D game
- Data center
- Changeing the frequency from IF to RF
- interconnection between switches
- Mainframes, workstations or storage devices
