MAX491EEPD+
| Parameters | |
|---|---|
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX491 |
| Pin Count | 14 |
| Output Voltage | 12.5V |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Nominal Supply Current | 500μA |
| Logic Function | Receiver, Transceiver |
| Data Rate | 2.5Mbps |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Full |
| Receiver Hysteresis | 70mV |
| Number of Transceivers | 1 |
| Simplex/Duplex | Full Duplex |
| Transmit Delay-Max | 60 ns |
| Output Low Current-Max | 0.004A |
| High Level Input Current-Max | 0.000002A |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
MAX491EEPD+ Overview
LED drivers with the enhanced 14-DIP (0.300, 7.62mm) package will be able to drive a variety of common LEDs with ease.In the Tube package, this receiver is mounted.It has proved to be a valuable component for a variety of applications since it is a Transceiver can transceiver.A Through Hole-type PCB or development board can be used to place this wide receiver.It takes 4.75V~5.25V from the power supply to run this differential driver.At any one time, this electronic part can have up to 1/1 eligible receivers/drivers.As its name implies, this ic receiver is designed for applications where -40°C~85°C is the operating temperature.With a supply voltage range of 5V, this line driver ic operates efficiently.This integrated circuit has 14 terminations designed for driving and receiving signals from data.The pinouts for this transceiver are standardized to meet the needs of the market.Since the base part number MAX491 uniquely identifies the product type, temperature, package, etc., you can use it to find more variations.The driver IC has improved power dissipation control.As a result of optical transceiver downsizing and high-density Through Hole mounting technologies, its package size has been greatly reduced.In terms of resolution, this ic receiver was capable of providing a 1-bit resolution.In the case of this receiver, a resolution of 1 bits is typically specified.There is a voltage supply of 5V required in order for this transceiver module to be operated.There is a subcategory named Line Driver or Receivers for this rf transceiver module.This driver IC is designed to operate from a 5V power supply.In total, there are 1 transceivers implemented by this module isolated transceiver.Wide receiver provides the output voltage of 12.5V.
MAX491EEPD+ Features
Tube package
14 pin count
14 pins
5V power supply
MAX491EEPD+ Applications
There are a lot of Maxim Integrated MAX491EEPD+ Drivers/Receivers/Transceivers applications.
- Long-distance fiber optic network applications
- Single to Multimode Fiber Conversion
- VoIP phones
- Shortwave receiver
- Wireless interactive experience
- Switches
- Tuner
- TV signal transmission
- Routers
- Remote controls
