MAX705EPA
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Power Management Circuits |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX705 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 500μA |
| Max Supply Current | 500μA |
| Adjustable Threshold | YES |
| Watchdog Timer | Yes |
| Reset | Active Low |
| Voltage - Threshold | 4.65V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 140ms Minimum |
| Min Reset Threshold Voltage | 4.5V |
| Max Reset Threshold Voltage | 4.75V |
| Undervoltage Threshold | 4.5V |
| Overvoltage Threshold | 4.75V |
| Height | 4.45mm |
| Length | 9.91mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX705EPA Overview
There are 8 mounting terminals on the voltage supervisor, each of which has a different function. Power management is packaged in a Tube way. Power management is possible to find a series of 1 functions. There are 2 channels available on this supervisor, and each channel has a different function. Please find attached 8-DIP (0.300, 7.62mm) functions for your reference in this IC power. It is a IC power that shares many benefits with other products from the Simple Reset/Power-On Reset line. IC management conducts at a voltage of 5V. IC management is possible to find a succession of 1 voltages that have been checked. The power management is mounted by Through Hole. In this case, this PMIC chip can be sub-categorized as a Power Management Circuits chip. It has a total of 8 pins that are attached to IC management. 8 pins are on the supervisor. I should note that the minimum supply voltage (Vsup) for this IC management should be at least 1.2V, which is the minimum supply voltage that should be applied. There should be no more than 5.5V volts of maximum supply voltage (Vsup) in this power management. The recommended mounting type is Through Hole. We recommend setting the supervisors to -40°C~85°C TA degrees. While in operation, this supervisor has a voltage output of Push-Pull, Totem Pole. It is estimated that the voltage supervisor's supply current is 500μA. To find similar IC managements from the manufacturer, you can always search by MAX705. It requires 5V watts of power to operate this voltage supervisor. Voltage supervisor can work with a supply temperature of 500μA at the most.
MAX705EPA Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
500μA operating supply current
MAX705EPA Applications
There are a lot of Maxim Integrated MAX705EPA Voltage Supervisors applications.
- Power distribution systems of ICU
- Automotive permanent magnet synchronous motors
- Important electronics for automotive safety
- Telecommunications equipment
- Microcontroller system
- FPGA design
- Digitally controlled LDO regulators circuit
- Important electronics for automotive protection
- Magnetic resonance imaging
- Efficient information transmission
