MC100EP51DR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| Series | 100EP |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 100EP51 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 450 ps |
| Turn On Delay Time | 375 ps |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 45mA |
| Halogen Free | Halogen Free |
| Prop. Delay@Nom-Sup | 0.5 ns |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 47mA |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 3000000000Hz |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC100EP51DR2G Overview
It is packaged in the way of 8-SOIC (0.154, 3.90mm Width). D flip flop is embedded in the Tape & Reel (TR) package. T flip flop uses Differentialas its output configuration. Positive, Negativeis the trigger it is configured with. Surface Mountis in the way of this electric part. Powered by a -3V~-5.5Vvolt supply, it operates as follows. A temperature of -40°C~85°C TAis used in the operation. A flip flop of this type is classified as a D-Type. FPGAs belonging to the 100EPseries contain this type of chip. You should not exceed 3GHzin its output frequency. As a result, it consumes 45mA of quiescent current without being affected by external factors. A total of 8terminations have been recorded. This D latch belongs to the family of 100EP51. A voltage of 3.3V is used as the power supply for this D latch. There is an electronic part that is mounted in the way of Surface Mount. This board is designed with 8pins on it. The clock edge trigger type for this device is Positive Edge. The part you are looking for is included in FF/Latches. It is designed with a number of bits of 1. It reaches 5.5Vwhen the maximum supply voltage (Vsup) is applied. For normal operation, the supply voltage (Vsup) should be above 3V. 1 circuits are used to achieve its superior flexibility. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TAPE AND REEL. The power supply is -4.5V. Additionally, there are NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V on the electronic flip flop that can be referred to. High level output current is set to -50mA. A 50mAvalue is set for low-level output current.
MC100EP51DR2G Features
Tape & Reel (TR) package
100EP series
8 pins
1 Bits
-4.5V power supplies
MC100EP51DR2G Applications
There are a lot of ON Semiconductor MC100EP51DR2G Flip Flops applications.
- Computers
- ESCC
- Supports Live Insertion
- Power down protection
- Reduced system switching noise
- Matched Rise and Fall
- EMI reduction circuitry
- Circuit Design
- Functionally equivalent to the MC10/100EL29
- Set-reset capability
