MC10EP51DTR2G
| Parameters | |
|---|---|
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -5.2V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 370 ps |
| Turn On Delay Time | 320 ps |
| Family | 10E |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 45mA |
| Halogen Free | Halogen Free |
| Prop. Delay@Nom-Sup | 0.42 ns |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 47mA |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 3000000000Hz |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| Series | 10EP |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 10EP51 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
MC10EP51DTR2G Overview
8-TSSOP, 8-MSOP (0.118, 3.00mm Width)is the way it is packaged. A package named Tape & Reel (TR)includes it. The output it is configured with uses Differential. It is configured with the trigger Positive, Negative. The electronic part is mounted in the way of Surface Mount. A voltage of -3V~-5.5Vis required for its operation. It is operating at -40°C~85°C TA. A flip flop of this type is classified as a D-Type. The FPGA belongs to the 10EP series. In order for it to function properly, its output frequency should not exceed 3GHz. It consumes 45mA of quiescent There are 8 terminations,This D latch belongs to the family of 10EP51. It is powered by a voltage of 3.3V . The electronic device belongs to the 10Efamily. There is an electronic component mounted in the way of Surface Mount. As you can see from the design, it has pins with 8. This device's clock edge trigger type is Positive Edge. The part is included in FF/Latches. There are 1bits in this flip flop. 5.5Vis the maximum supply voltage (Vsup). It is imperative that the supply voltage (Vsup) is maintained above 3Vin order to ensure normal operation. Its flexibility is enhanced by 1 circuits. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. An electrical current of -5.2V volts is applied to it. Additionally, you may refer to the additional NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V of the electronic flip flop. -50mA is set as the high level output current. It is set to 50mAfor the low level output current.
MC10EP51DTR2G Features
Tape & Reel (TR) package
10EP series
8 pins
1 Bits
-5.2V power supplies
MC10EP51DTR2G Applications
There are a lot of ON Semiconductor MC10EP51DTR2G Flip Flops applications.
- Automotive
- Consumer
- Synchronous counter
- Reduced system switching noise
- Circuit Design
- ESD protection
- High Performance Logic for test systems
- ATE
- Count Modes
- Common Clocks
