MC74HC273AFELG
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC273 |
| Function | Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 35MHz |
| Propagation Delay | 145 ns |
| Turn On Delay Time | 25 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 25ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.05mm |
| Width | 5.275mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC74HC273AFELG Overview
The flip flop is packaged in 20-SOIC (0.209, 5.30mm Width). It is contained within the Tape & Reel (TR)package. There is a Non-Invertedoutput configured with it. It is configured with the trigger Positive Edge. The electronic part is mounted in the way of Surface Mount. A voltage of 2V~6Vis required for its operation. Temperature is set to -55°C~125°C TA. D-Typedescribes this flip flop. In this case, it is a type of FPGA belonging to the 74HC series. This D flip flop should not have a frequency greater than 35MHz. There are 1 elements in it. It consumes 4μA of quiescent A total of 20terminations have been recorded. It is a member of the 74HC273 family. It is powered by a voltage of 3V . A 10pFfarad input capacitance is provided by this T flip flop. An electronic device belonging to the family HC/UHcan be found here. The electronic part is mounted in the way of Surface Mount. 20pins are included in its design. Its clock edge trigger type is Positive Edge. This part is included in FF/Latches. There are 8bits in this flip flop. In this case, the maximum supply voltage (Vsup) reaches 6V. Normally, the supply voltage (Vsup) should be kept above 2V. The superior flexibility of this circuit is achieved by using 8 circuits. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. The system runs on a power supply of 2/6V watts.
MC74HC273AFELG Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
MC74HC273AFELG Applications
There are a lot of ON Semiconductor MC74HC273AFELG Flip Flops applications.
- Latch-up performance
- Computing
- Divide a clock signal by 2 or 4
- Modulo – n – counter
- Computers
- Memory
- QML qualified product
- ESCC
- Matched Rise and Fall
- Clock pulse
