MC74VHCT374ADTRG
| Parameters | |
|---|---|
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 95000000Hz |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74VHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74VHCT374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 130MHz |
| Propagation Delay | 10.4 ns |
| Turn On Delay Time | 4.1 ns |
| Family | AHCT/VHCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 8mA 8mA |
MC74VHCT374ADTRG Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). A package named Tape & Reel (TR)includes it. T flip flop is configured with an output of Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. Surface Mountis in the way of this electric part. It operates with a supply voltage of 4.5V~5.5V. It is operating at -40°C~85°C TA. This D latch has the type D-Type. JK flip flop is a part of the 74VHCTseries of FPGAs. Its output frequency should not exceed 130MHz Hz. In total, it contains 1 elements. During its operation, it consumes 4μA quiescent energy. It has been determined that there have been 20 terminations. This D latch belongs to the family of 74VHCT374. The power source is powered by 5V. Its input capacitance is 4pF farads. AHCT/VHCTis the family of this D flip flop. Surface Mount mounts this electronic component. This board is designed with 20pins on it. A Positive Edgeclock edge trigger is used in this device. The RS flip flops belongs to FF/Latches base part number. The flip flop is designed with 8bits. The superior flexibility of this circuit is achieved by using 8 circuits. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. A total of 5V power supplies are needed to run it. The D flip flop has no ports embedded. In order to ensure high efficiency, the supply voltage should remain at 5V. The JK flip flop is with 3 output lines to operate.
MC74VHCT374ADTRG Features
Tape & Reel (TR) package
74VHCT series
20 pins
8 Bits
5V power supplies
MC74VHCT374ADTRG Applications
There are a lot of ON Semiconductor MC74VHCT374ADTRG Flip Flops applications.
- Dynamic threshold performance
- Computers
- Single Up Count-Control Line
- Instrumentation
- Memory
- Storage registers
- Divide a clock signal by 2 or 4
- Supports Live Insertion
- Load Control
- Data Synchronizers
