MCP6002-E/MC
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6002 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5.5V |
| Number of Elements | 2 |
| Number of Circuits | 2 |
| Nominal Supply Current | 100μA |
| Output Current | 23mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 4.5mV |
| Gain Bandwidth Product | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 112dB |
| Power Supply Rejection Ratio (PSRR) | 86dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | NO |
| Micropower | YES |
| Max Frequency | 1kHz |
| Programmable Power | NO |
| Wideband | NO |
| Height | 950μm |
| Length | 2mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6002-E/MC Overview
The linear amplifier is packaged in a 8-VFDFN Exposed Pad case. There are two types of operational amplifiers in this circuit. Instrumentation amplifier is delivered in a Tube case. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins. Please take in mind that op amp should be run at 5V. It should be noted that this op amp is a type of Operational Amplifier device. Linear amplifier includes 8 pins. In terms of input offset voltage, operational amplifier rates 4.5mV. The mounting type that is recommended for this electrical part is Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureIt is recommended to keep the voltage gain at 112dB at all times. This op amp ic has 2 circuits. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. A total of 2 elements are present in this linear amplifier. The operating supply voltage of instrumentation amplifier is rated 5.5V voltage.
MCP6002-E/MC Features
8 Pins
supply voltage of 5V
112dB voltage gain
Output Type: Rail-to-Rail
MCP6002-E/MC Applications
There are a lot of Microchip Technology MCP6002-E/MC Instrumentational OP Amps applications.
- Proportional counter tubes
- Industrial control system
- Large motor controllers
- Weighing systems
- Portable electronic products powered by batteries
- Semiconductor detectors
- Power control
- High/low-pass filter circuit
- Band-stop filter
- Television broadcasting equipment
