MCP6021-I/ST
| Parameters | |
|---|---|
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 30mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 1mm |
| Length | 3mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6021 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Nominal Supply Current | 1mA |
| Output Current | 22mA |
| Current - Supply | 1mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 74dB |
MCP6021-I/ST Overview
Packaged in a 8-TSSOP (0.173, 4.40mm Width) case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. Upon delivery, op amp ic is packaged in a Tube case. In recent months, the number of terminations has approached 8. A total of 8 pins are attached to buffer op amp. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. It has 5 pins that make up the linear amplifier. Op amp ic rates 500μV for input offset voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. With regard to operating temperature, op amp ranges -40°C~85°C. The voltage gain should stay at 110dB. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The buffer op amp is rated for an operating voltage of 1 when it comes to the power supply. As a result, it is recommended that a power supply of 1mA be used with this electronic part.
MCP6021-I/ST Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
MCP6021-I/ST Applications
There are a lot of Microchip Technology MCP6021-I/ST Instrumentational OP Amps applications.
- Commercial audio systems
- Broadcasting
- High input resistance broadband
- Medical imaging
- Non-polarized electrodes
- Logarithmic operation circuits
- pH (acidity)
- Large motor controllers
- Strain gauges
- Differentiator circuits
