MCP6143T-E/CH
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6143 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Nominal Supply Current | 600nA |
| Output Current | 21mA |
| Current - Supply | 600nA |
| Slew Rate | 0.003V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.4V~6V |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 100 kHz |
| Unity Gain BW-Nom | 100 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Supply Voltage Limit-Max | 7V |
| Current - Output / Channel | 20mA |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MCP6143T-E/CH Overview
In the package, you will find a SOT-23-6-case to contain the op amp ic. This is a General Purpose type op amp. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. A total of 6 terminations have been reported in the past few weeks. In this case, there are 6 pins on the board. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 6 pins are located on the operational amplifiers. Regarding input offset voltage, op amp rates 3mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . Op amp is a member of the 115dB's 115dB family. Op amp ic has 1 channels. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted. For optimal performance, this electrical part should be connected to a supply with a current of 600nA.
MCP6143T-E/CH Features
6 Pins
supply voltage of 5V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6143T-E/CH Applications
There are a lot of Microchip Technology MCP6143T-E/CH Instrumentational OP Amps applications.
- Image computer boards
- Television broadcasting equipment
- High input resistance broadband
- Differentiator circuits
- Instrumentation
- Portable electronic products powered by batteries
- Logarithmic operation circuits
- Video data acquisition
- RF cable systems
- Television
