MCP635T-E/MF
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP635 |
| Pin Count | 10 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Power Supplies | 3/5V |
| Operating Supply Current | 2.5mA |
| Nominal Supply Current | 2.5mA |
| Output Current | 70mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 63 dB |
| Current - Input Bias | 4pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 1.8mV |
| Gain Bandwidth Product | 24MHz |
| Unity Gain BW-Nom | 24000 kHz |
| Voltage Gain | 124dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 61dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6.5V |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MCP635T-E/MF Overview
Packaged in a 10-VFDFN Exposed Pad case, the buffer op amp is ready to use. A General Purpose-type buffer amplifier is shown here. It comes in a Tape & Reel (TR) case, which protects instrumentation amplifier from damage during delivery. The number of terminations is approaching the 10 mark. The total number of pins on linear amplifier is 10. Please take in mind that op amp should be run at 2.5V. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The buffer op amp includes 10 pins. Regarding input offset voltage, buffer amplifier rates 1.8mV voltage. For this electrical component, Surface Mount is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. Using a supply current of 2.5mA , this buffer op amp will be able to operate. The voltage gain should stay at 124dB. On the output type, there are Rail-to-Rail different types of op amps. According to the specifications of the buffer op amp, the operating supply voltage is rated at 2. The linear amplifier is packaged by using a TAPE AND REEL axis.
MCP635T-E/MF Features
10 Pins
supply voltage of 2.5V
124dB voltage gain
Output Type: Rail-to-Rail
MCP635T-E/MF Applications
There are a lot of Microchip Technology MCP635T-E/MF Instrumentational OP Amps applications.
- Addition operation circuits
- Non-polarized electrodes
- Signal filtering
- RF cable systems
- Digital cameras
- Measurements of Wheatstone bridge
- Wireless base stations
- Voltage regulation circuit
- Ultrasound transducers
- MP3
