MCP6H74-E/SL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6H74 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 6V |
| Power Supplies | +-1.75/+-6/3.5/12V |
| Number of Channels | 4 |
| Operating Supply Current | 480μA |
| Nominal Supply Current | 480μA |
| Slew Rate | 2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 76 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 3.5V~12V ±1.75V~6V |
| Output Current per Channel | 32mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 2.7MHz |
| Unity Gain BW-Nom | 2700 kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 82dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 13.2V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 10kHz |
| Height | 1.5mm |
| Length | 8.65mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6H74-E/SL Overview
A 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. Op amps are General Purpose types of amplifier on the chip. The op amp is delivered to you in a Tube case. During the past two weeks, there have been close to 14 terminations. I would like to remind you that this buffer op amp should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. 14 pins are available on the instrumentation amplifier. In terms of input offset voltage, operational amplifier rates 1mV. For this electrical component, Surface Mount is the recommended mounting type. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . An 480μA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain at 120dB. Instrumentation amplifier has 4 channels on it. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The operating supply voltage of the buffer op amp is rated at 6V.
MCP6H74-E/SL Features
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
MCP6H74-E/SL Applications
There are a lot of Microchip Technology MCP6H74-E/SL Instrumentational OP Amps applications.
- Television broadcasting equipment
- High input resistance broadband
- Video amplifiers
- Blood pressure sensors
- Subtraction operation circuits
- Image computer boards
- Proportional operation circuits
- Gaming industry
- ECG equipment
- Non-polarized electrodes
