MCP6L01UT-E/OT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6L01U |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Nominal Supply Current | 85μA |
| Output Current | 20mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 78 dB |
| Current - Input Bias | 2pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~6V |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 105dB |
| Power Supply Rejection Ratio (PSRR) | 83dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 1mV |
| Low-Bias | YES |
| Micropower | YES |
| Height | 1.3mm |
| Length | 3.1mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6L01UT-E/OT Overview
A SC-74A, SOT-753 case is used to package the op amp. Op amps are General Purpose types of amplifier on the chip. A Tape & Reel (TR) case is used for delivering the op amp. A total of 5 terminations have been reported in the past few weeks. Linear amplifier has a total of 5 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 5 pins are available on the instrumentation amplifier. Op amp ic rates 5mV for input offset voltage. This electrical part should be mounted using type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureKeeping the voltage gain at 105dB is the best course of action. A instrumentation amplifier like this has 1 circuits. On the buffer amps, there are 1 channels that can be used. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. An buffer amplifier is packed in a TAPE AND REEL-shape according to the design.
MCP6L01UT-E/OT Features
5 Pins
supply voltage of 5V
105dB voltage gain
Output Type: Rail-to-Rail
MCP6L01UT-E/OT Applications
There are a lot of Microchip Technology MCP6L01UT-E/OT Instrumentational OP Amps applications.
- Portable docking station
- High/low-pass filter circuit
- Communication
- Video amplifiers
- single/dual op amp sum and difference circuits
- Blood pressure sensors
- Micro signal measurement
- Radar
- Power transmission
- Vehicle electronics
