MIC2505-1YM
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Supplier Device Package | 8-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1998 |
| Feature | Slew Rate Controlled, Status Flag |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 30mOhm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Current Rating | 2A |
| Base Part Number | MIC2505 |
| Number of Outputs | 1 |
| Output Voltage | 7.5V |
| Output Type | N-Channel |
| Max Output Current | 2A |
| Number of Channels | 1 |
| Interface | On/Off |
| Max Supply Voltage | 7.5V |
| Min Supply Voltage | 2.7V |
| Current - Output (Max) | 2A |
| Nominal Supply Current | 2A |
| Output Configuration | High Side |
| Output Current | 2A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 2 ms |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 7.5V |
| Nominal Input Voltage | 7.5V |
| Turn-Off Delay Time | 20 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~7.5V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, UVLO |
| Rds On (Typ) | 30mOhm |
| Drain to Source Resistance | 35mOhm |
| Height | 1.48mm |
| Length | 4.93mm |
| Width | 3.94mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MIC2505-1YM Overview
It is packaged in the manner of a Tube.Package 8-SOIC (0.154, 3.90mm Width) contains it.The LED driver is mounted as Surface Mount.A General Purpose switch type is owned by it.It is best to set the temperature to -40°C~85°C TA to ensure reliable operation.In this LED driver, there are no outputs available.A supply voltage of Not Required is required for it to operate.Voltage output is N-Channel volts at maximum.This LED driving board is equipped with Slew Rate Controlled, Status Flag features in order for it to be useful.It is part of the MIC2505 family of LED drivers.In order to operate, the 8 pins are used.The lighting driver's maximum output is 2AV.This operation requires the maximum output current to be decreased to 2A.In this case, it is mounted in the way of Surface Mount.30mOhm is the resistance of the lighting driver.This results in a 2A output current.In total, 1 channels are available.This LED driver can handle voltages up to 7.5V volts.Input voltage must be at least 2.7V volts.For stable operation, the maximum operating temperature should be 85°C°C.In order to ensure reliability, it must operate at a minimum temperature of -40°C degrees Celsius.A maximum supply voltage of 7.5VV can be handled by the LED driving board.It is possible to use a voltage as low as 2.7V V as a power supply voltage.
MIC2505-1YM Features
Resistance of 30mOhm
1 channels
MIC2505-1YM Applications
There are a lot of Microchip Technology MIC2505-1YM Power Switches ICs applications.
- Low Voltage I/O System Power
- Portable Music Players
- Hot Swaps
- Storage Drives
- Wearable Devices
- Portable Devices
- Portable GPS
- Solid-State Drives
- PC Card Hot Swap
- Portable/Handheld Devices
