MM74HC273SJX
| Parameters | |
|---|---|
| Turn On Delay Time | 18 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 23ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 7pF |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Width | 5.3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 481.5mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | 74HC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 4.5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 78MHz |
| Propagation Delay | 23 ns |
| Quiescent Current | 8μA |
MM74HC273SJX Overview
The package is in the form of 20-SOIC (0.209, 5.30mm Width). A package named Tape & Reel (TR)includes it. In the configuration, Non-Invertedis used as the output. There is a trigger configured with Positive Edge. There is an electronic component mounted in the way of Surface Mount. It operates with a supply voltage of 2V~6V. In the operating environment, the temperature is -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. JK flip flop is a part of the 74HCseries of FPGAs. Its output frequency should not exceed 78MHz Hz. The element count is 1 . There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. If you search by 74HC273, you will find similar parts. Power is supplied from a voltage of 4.5V volts. This T flip flop has a capacitance of 7pF farads at the input. An electronic device belonging to the family HC/UHcan be found here. Electronic part Surface Mountis mounted in the way. The electronic flip flop is designed with pins 20. This device has Positive Edgeas its clock edge trigger type. This part is included in FF/Latches. There are 8bits in its design. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be kept above 2V. Due to its superior flexibility, it uses 8 circuits. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. The D latch operates on 2/6V volts. It consumes 8μA current.
MM74HC273SJX Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
MM74HC273SJX Applications
There are a lot of ON Semiconductor MM74HC273SJX Flip Flops applications.
- QML qualified product
- Computing
- Storage Registers
- Divide a clock signal by 2 or 4
- Data Synchronizers
- Pattern generators
- ATE
- Single Down Count-Control Line
- Guaranteed simultaneous switching noise level
- Latch-up performance
