NB2305AI1HDTR2G
| Parameters | |
|---|---|
| Number of Circuits | 1 |
| Nominal Supply Current | 50mA |
| Max Supply Current | 50mA |
| Frequency (Max) | 133MHz |
| Halogen Free | Halogen Free |
| Input | CMOS |
| Ratio - Input:Output | 1:5 |
| PLL | Yes |
| Differential - Input:Output | No/No |
| Same Edge Skew-Max (tskwd) | 0.25 ns |
| Number of True Outputs | 4 |
| Height | 950μm |
| Length | 3.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| Type | Zero Delay Buffer |
| Terminal Finish | Tin (Sn) |
| Subcategory | Clock Drivers |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NB2305A |
| Pin Count | 8 |
| Operating Supply Voltage | 3.3V |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 3V |
NB2305AI1HDTR2G Overview
A clock integrated circuit is packaged in a Tape & Reel (TR)-shaped package because it is for use as a clock. The 8-TSSOP (0.173, 4.40mm Width) package includes this clock generator. This clock generator ic can sustain a maximum temperature of 260 during reflowing. It contains a total of 8 terminations within RF synthesizer. Basically, a voltage of 3.3V should be applied to this electronic frequency generator. This Clock PLL will be fed by CMOS as its input. A total of 1 circuits are implemented to access the full performance of the electrical part. Using this clock-based frequency synthesizer, you can achieve a maximum frequency of 133MHz. The Surface Mount allows the electrical component to be installed conveniently on the panel. The maximum voltage this clock PLL can handle is 3.6V. There should be a voltage supply above 3V for this frequency generator in order to ensure its safety. There are 3V~3.6V available for use with this clock PLL. As determined by the test statistics, the ambient temperature should be set to -40°C~85°C. As far as this electronic part is concerned, it can be classified as a Zero Delay Buffer component. In particular, this clock PLL is designed to be used with microprocessors. Related electrical parts can be found for the base part number NB2305A. The frequency generator is equipped with 8 pins. Supply voltage 3.3V is what time clock generator can handle. A Clock Drivers clock generator is essentially what this device is. There is a low timing skew at 0.25 nsmax with this RF synthesizer. The digital clock generator has 4 high-enable output pins. During this clock generator operation, a maximum current of 50mA is supplied.
NB2305AI1HDTR2G Features
Available in the 8-TSSOP (0.173, 4.40mm Width)
Supply voltage of 3.3V
Operating supply voltage of 3.3V
4 true outputs
NB2305AI1HDTR2G Applications
There are a lot of ON Semiconductor NB2305AI1HDTR2G Clock Generators applications.
- Carrier synchronization in wired communication
- Electronic equipment
- Coherent detection of the signal
- Wireless handsets
- Signal modulation and demodulation
- Myriad digital applications
- Sampling clocks for ADC and DAC
- Aerospace and defense
- Test equipment
- Bluetooth receivers
