NLAS4684MR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 1Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | NLAS4684 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 200nA |
| Turn On Delay Time | 50 ns |
| Halogen Free | Halogen Free |
| Supply Type | Single |
| Turn-Off Delay Time | 60 ns |
| -3db Bandwidth | 9.5MHz |
| On-State Resistance (Max) | 800mOhm |
| High Level Output Current | 300mA |
| Low Level Output Current | 300mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 102pF 104pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 30ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -83dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height | 950μm |
| Length | 3.1mm |
| Width | 3.1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NLAS4684MR2G Overview
Due to its 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 2:1. An extended operating temperature of -55°C~125°C TA degrees Celsius. In total, there have been 10 terminations. By its 2 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. It is injected into the electrical part body with 10 pins. SPDT switching circuits are used in these analog switch ics. Using the NLAS4684 search parameter, you can discover variants of the switch. It has an internal resistance of 1Ohm. For details about the functions of 10 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 1.8V. In order to operate this switch device, it would need a current of 200nA. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. 5V operating voltages can be used with this electrical part. 4 outputs are included in the analogue multiplexer.
NLAS4684MR2G Features
2 Channels
Switch Circuit: SPDT
200nA Supply Current
-3db Bandwidth: 9.5MHz
NLAS4684MR2G Applications
There are a lot of ON Semiconductor NLAS4684MR2G Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- SDH
- E1 Network Equipment
- Intelligent PBX
- ISDN NT1/TA
- 65 V DACs
- Power routing
- Ultrasound
- Communication systems
- Avionics and Military Systems
