OP1177ARM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP1177 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 500μA |
| Quiescent Current | 500μA |
| Supply Current-Max | 0.6mA |
| Slew Rate | 0.7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 125 dB |
| Current - Input Bias | 500pA |
| Voltage - Supply, Single/Dual (±) | 5V~36V ±2.5V~18V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 60μV |
| Gain Bandwidth Product | 1.3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 1300 kHz |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.002μA |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 15μV |
| Low-Bias | NO |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Input Voltage Noise Density | 7.9nV/sqrt Hz |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP1177ARM-REEL Overview
In the package, you will find a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case to contain the op amp ic. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. In total, the buffer amplifier consists of 8 pins. In terms of the input offset voltage, instrumentation amplifier rates at 60μV. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~125°C. An 500μA volt supply current is needed for this linear amplifier to operate. Keeping the voltage gain at 126.02dB is the best course of action. Instrumentation amplifier has 1 channels on it. TAPE AND REEL is adopted to pack the instrumentation amplifier. The quiescent current is 500μA.
OP1177ARM-REEL Features
8 Pins
supply voltage of 5V
126.02dB voltage gain
OP1177ARM-REEL Applications
There are a lot of Analog Devices Inc. OP1177ARM-REEL Instrumentational OP Amps applications.
- Band-pass filter
- High-frequency data acquisition systems
- Industrial applications including automation
- PDA
- Logarithmic operation circuits
- single/dual op amp sum and difference circuits
- Addition operation circuits
- Integrator circuits
- Fast A/D and D/A converters
- Information processing
