OP284ESZ-REEL7
| Parameters | |
|---|---|
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP284 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 4mA |
| Quiescent Current | 2mA |
| Supply Current-Max | 4.5mA |
| Slew Rate | 4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 80nA |
| Voltage - Supply, Single/Dual (±) | 3V~36V ±1.5V~18V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 100μV |
| Gain Bandwidth Product | 4.25MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4250 kHz |
| Voltage Gain | 107.6dB |
| Average Bias Current-Max (IIB) | 0.575μA |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Settling Time | 4 μs |
| Input Voltage Noise Density | 3.9nV/sqrt Hz |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
OP284ESZ-REEL7 Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case. The instrumentation amplifier in this picture is of the General Purpose-type. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. It is estimated that there will be at least 8 terminations this year. Buffer amplifier has a total of 8 pins on it. I would like to remind you that this buffer op amp should be powered by an 15V battery. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. The op amp ic has an array of 8 pins on it. As far as the input offset voltage is concerned, linear amplifier rates at 100μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . It is possible to operate this buffer amplifier from a supply current of 4mA . It is a member of the 107.6dB's 107.6dB family. There are 2 channels on the operational amplifiers. On the output type, there are Rail-to-Rail different types of op amps. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. As a result, linear amplifier's quiescent current is 2mA.
OP284ESZ-REEL7 Features
8 Pins
supply voltage of 15V
107.6dB voltage gain
Output Type: Rail-to-Rail
OP284ESZ-REEL7 Applications
There are a lot of Analog Devices Inc. OP284ESZ-REEL7 Instrumentational OP Amps applications.
- Logarithmic operation circuits
- Semiconductor detectors
- Comparator
- Weak signal detection
- Differentiator circuits
- Industrial applications including automation
- Test equipment
- Proportional operation circuits
- Addition operation circuits
- Subtraction operation circuits
