OP467GP
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Operational Amplifier |
| Technology | BIPOLAR |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | OP467 |
| Pin Count | 14 |
| Number of Channels | 4 |
| Operating Supply Current | 8mA |
| Nominal Supply Current | 8mA |
| Quiescent Current | 2.5mA |
| Slew Rate | 350V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 150nA |
| Voltage - Supply, Single/Dual (±) | ±4.5V~18V |
| Supply Type | Dual |
| Input Offset Voltage (Vos) | 200μV |
| Gain Bandwidth Product | 28MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 22000 kHz |
| Voltage Gain | 83dB |
| Average Bias Current-Max (IIB) | 0.7μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Bias Current-Max (IIB) @25C | 0.6μA |
| Dual Supply Voltage | 15V |
| Input Capacitance | 2pF |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Voltage Noise Density | 7nV/sqrt Hz |
| Height Seated (Max) | 5.33mm |
| Length | 19.05mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
OP467GP Overview
A 14-DIP (0.300, 7.62mm) case is used to package the op amp. General Purpose-type instrumentation amplifiers are used in this application. Upon delivery, op amp ic is packaged in a Tube case. In recent months, the number of terminations has approached 14. The total number of pins on linear amplifier is 14. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. In total, the buffer amplifier consists of 14 pins. There is an input offset voltage of 200μV for this buffer op amp. This electrical part should be mounted using type Through Hole. With regard to operating temperature, op amp ranges -40°C~85°C. A supply current of 8mA can be used to operate this linear amplifier. It is recommended to keep the voltage gain at 83dB at all times. As far as the device is concerned, buffer amplifier has 4 channels. 2.5mA quiescent currents are flowing through buffer op amp.
OP467GP Features
14 Pins
supply voltage of 5V
83dB voltage gain
OP467GP Applications
There are a lot of Analog Devices Inc. OP467GP Instrumentational OP Amps applications.
- Automation control systems
- Industrial control system
- Differentiator circuits
- Vehicle electronics
- Radar
- Blood pressure sensors
- Integrator circuits
- Tablets
- Voltage regulation circuit
- Power generator
