Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Contact Plating |
Gold |
Mounting Type |
Surface Mount |
Package / Case |
SC-74A, SOT-753 |
Surface Mount |
YES |
Number of Pins |
5 |
Operating Temperature |
-40°C~85°C |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
2 (1 Year) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Subcategory |
Operational Amplifier |
Packing Method |
TR |
Technology |
BIPOLAR |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
6V |
Base Part Number |
OPA659 |
Pin Count |
5 |
Number of Channels |
1 |
Operating Supply Current |
32mA |
Slew Rate |
2550V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
J-FET |
Common Mode Rejection Ratio |
68 dB |
Current - Input Bias |
10pA |
Voltage - Supply, Single/Dual (±) |
±3.5V~6.5V |
Output Current per Channel |
70mA |
Input Offset Voltage (Vos) |
5mV |
Bandwidth |
650MHz |
Gain Bandwidth Product |
350MHz |
Neg Supply Voltage-Nom (Vsup) |
-6V |
Unity Gain BW-Nom |
650000 kHz |
Voltage Gain |
58dB |
Average Bias Current-Max (IIB) |
0.0032μA |
Power Supply Rejection Ratio (PSRR) |
58dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
1mV |
Low-Bias |
YES |
Micropower |
NO |
Max Frequency |
10MHz |
Programmable Power |
NO |
Dual Supply Voltage |
6V |
Max I/O Voltage |
5mV |
Height |
1.45mm |
Length |
2.9mm |
Width |
1.6mm |
Thickness |
1.2mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
OPA659IDBVT Overview
In the package, you will find a SC-74A, SOT-753-case to contain the op amp ic. The instrumentation amplifier in this picture is of the J-FET-type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. There have been a total of 5 terminations over the past year. In this case, there are 5 pins on the board. As a reminder, this buffer op amp should be powered by 6V battery and that the battery should be inserted in the amplifier. To be specific, this instrumentation amplifier is a type of Operational Amplifier. The buffer op amp includes 5 pins. As far as the input offset voltage is concerned, linear amplifier rates at 5mV. For this electronic part, it is recommended that you mount it with type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. As long as the supply current of the chip does not exceed 32mA, this op amp ic can operate. 58dB should be the voltage gain. Op amp ic has 1 channels. A TR-shaped amplifier is used to pack the buffer amps.
OPA659IDBVT Features
5 Pins
supply voltage of 6V
58dB voltage gain
OPA659IDBVT Applications
There are a lot of Texas Instruments OPA659IDBVT Instrumentational OP Amps applications.
- Cinema or auditorium audio system
- Signal amplification
- Comparator
- Test equipment
- Power generator
- Broadcasting
- E-book readers
- Industrial applications including automation
- Proportional operation circuits
- single/dual op amp sum and difference circuits