SN65HVD21DR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | 65HVD21 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-485 |
| Nominal Supply Current | 8mA |
| Data Rate | 5Mbps |
| Output Characteristics | 3-STATE |
| Differential Output | YES |
| Output Polarity | TRUE |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 130mV |
| Number of Transceivers | 1 |
| ESD Protection | Yes |
| Receive Delay-Max | 50 ns |
| Simplex/Duplex | Half Duplex |
| Transmit Delay-Max | 60 ns |
| Supply Voltage1-Nom | 5V |
| Max Junction Temperature (Tj) | 130°C |
| Ambient Temperature Range High | 85°C |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN65HVD21DR Overview
Designed for common LEDs, this driver IC features an enhanced 8-SOIC (0.154, 3.90mm Width) package.The package of this receiver is Tape & Reel (TR).It has proved to be a valuable component for a variety of applications since it is a Transceiver can transceiver.This wide receiver can be placed on any Surface Mount-type PCB or development board.This differential driver requires a 4.5V~5.5V power supply.Up to 1/1 receivers/drivers can be installed simultaneously on this electronic part.In most applications, this ic receiver is used in environments where -40°C~85°C is the operating temperature.Driver ICs in this category can operate efficiently with a supply voltage range of 5V.This integrated circuit has 8 terminations designed for driving and receiving signals from data.As a standard package, this transceiver comes with a 8-pin layout that follows the market standard.For more variants of this part, try searching with the base part number 65HVD21, which indicates the product type, temperature, package, etc.8-pin driver chip with enhanced power dissipation.Optical transceiver package size is greatly reduced due to downsizing of the ICs and high-density Surface Mount mounting technologies.In terms of resolution, this ic receiver was capable of providing a 1-bit resolution.Typically, the resolution of this receiver is specified to be 1 bits.There is a voltage input supply of 5V required for the operation of this integrated circuit.A Line Driver or Receivers subcategory can be assigned to this rf transceiver module.The driver IC in this product is designed so that it can be powered by 5V.The module isolated transceiver implements a total of 1 transceivers.
SN65HVD21DR Features
Tape & Reel (TR) package
8 pin count
8 pins
5V power supply
SN65HVD21DR Applications
There are a lot of Texas Instruments SN65HVD21DR Drivers/Receivers/Transceivers applications.
- Televisions
- Notebook
- Satellite radio receiver
- TV signal transmission
- Transmission stations
- Bar, KTV wireless entertainment
- Wireless interactive experience
- Satellite ground stations
- Single fiber bidirectional application
- Aircraft navigation
