SN74AHC273PWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 17.1 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 70000000Hz |
| Height | 1.15mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHC273PWRG4 Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). There is an embedded version in the package Tape & Reel (TR). T flip flop uses Non-Invertedas its output configuration. In the configuration of the trigger, Positive Edgeis used. In this case, the electronic component is mounted in the way of Surface Mount. The supply voltage is set to 2V~5.5V. In the operating environment, the temperature is -40°C~125°C TA. D-Typeis the type of this D latch. JK flip flop is a part of the 74AHCseries of FPGAs. Its output frequency should not exceed 110MHz. In total, there are 1 elements. There is a consumption of 4μAof quiescent energy. A total of 20 terminations have been made. The object belongs to the 74AHC273 family. It is powered from a supply voltage of 3.3V. A JK flip flop with a 2.5pFfarad input capacitance is used here. An electronic device belonging to the family AHC/VHC/H/U/Vcan be found here. It is mounted by the way of Surface Mount. A total of 20pins are provided on this board. This device's clock edge trigger type is Positive Edge. This RS flip flops is a part number FF/Latches. It is designed with a number of bits of 8. It reaches 5.5Vwhen the supply voltage is maximal (Vsup). The supply voltage (Vsup) should be kept above 2V for normal operation. Due to its superior flexibility, it uses 8 circuits. In light of its reliable performance, this T flip flop is well suited for TR. In order for the device to operate, it requires 2/5.5V power supplies. Its output current of 8mAallows for maximum design flexibility. Currently, there are 3 input lines present.
SN74AHC273PWRG4 Features
Tape & Reel (TR) package
74AHC series
20 pins
8 Bits
2/5.5V power supplies
SN74AHC273PWRG4 Applications
There are a lot of Texas Instruments SN74AHC273PWRG4 Flip Flops applications.
- Matched Rise and Fall
- Latch-up performance
- Storage Registers
- Control circuits
- Test & Measurement
- Guaranteed simultaneous switching noise level
- Computers
- Pattern generators
- Computing
- Frequency Dividers
