SN74AHCT374PW
| Parameters | |
|---|---|
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 130MHz |
| Propagation Delay | 12.5 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
SN74AHCT374PW Overview
20-TSSOP (0.173, 4.40mm Width)is the way it is packaged. Package Tubeembeds it. As configured, the output uses Tri-State, Non-Inverted. Positive Edgeis the trigger it is configured with. Surface Mountmounts this electrical part. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. Currently, the operating temperature is -40°C~85°C TA. There is D-Type type of electronic flip flop associated with this device. In terms of FPGAs, it belongs to the 74AHCT series. This D flip flop should not have a frequency greater than 130MHz. D latch consists of 1 elements. During its operation, it consumes 4μA quiescent energy. A total of 20terminations have been recorded. The object belongs to the 74AHCT374 family. The power source is powered by 5V. A 4pFfarad input capacitance is provided by this T flip flop. Devices in the AHCT/VHCT/VTfamily are electronic devices. In this case, the electronic component is mounted in the way of Surface Mount. 20pins are included in its design. Its clock edge trigger type is Positive Edge. The part you are looking for is included in FF/Latches. The design is based on 8bits. The superior flexibility of this circuit is achieved by using 8 circuits. The D latch runs on a voltage of 5V volts. There are 2 ports embedded in the flip flops. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. The output current of 8mA makes it feature maximum design flexibility. 3input lines are available for you to choose from.
SN74AHCT374PW Features
Tube package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT374PW Applications
There are a lot of Texas Instruments SN74AHCT374PW Flip Flops applications.
- Storage Registers
- Data storage
- Buffer registers
- Set-reset capability
- Latch-up performance
- Data Synchronizers
- Event Detectors
- Test & Measurement
- Single Down Count-Control Line
- Synchronous counter
