SN74HC273DW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Nominal Supply Current | 8μA |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 13 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 13ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 2 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Max Junction Temperature (Tj) | 150°C |
| Ambient Temperature Range High | 85°C |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC273DW Overview
The flip flop is packaged in 20-SOIC (0.295, 7.50mm Width). You can find it in the Tubepackage. There is a Non-Invertedoutput configured with it. The trigger configured with it uses Positive Edge. The electronic part is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2V~6V. Currently, the operating temperature is -40°C~85°C TA. D-Typedescribes this flip flop. The 74HCseries comprises this type of FPGA. A frequency of 60MHzshould be the maximum output frequency. Terminations are 20. This D latch belongs to the family of 74HC273. The D flip flop is powered by a voltage of 5V . There is 3pF input capacitance for this T flip flop. HC/UHis the family of this D flip flop. A part of the electronic system is mounted in the way of Surface Mount. A total of 20pins are provided on this board. In this device, the clock edge trigger type is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. Vsup reaches its maximum value at 6V. Normal operation requires a supply voltage (Vsup) above 2V. The supply voltage should be maintained at 5V for high efficiency. Its output current of 5.2mAallows for maximum design flexibility. There are 1 output lines in this JK flip flop. Currently, there are 2 lines of input. It consumes a total of 8μA quiescent current at any given time. As an additional reference, you may refer to electronic flip flop DUMMY VAL. There are 8 channels available.
SN74HC273DW Features
Tube package
74HC series
20 pins
SN74HC273DW Applications
There are a lot of Texas Instruments SN74HC273DW Flip Flops applications.
- Set-reset capability
- Power down protection
- Memory
- Dynamic threshold performance
- Data storage
- Count Modes
- Shift registers
- Parallel data storage
- Cold spare funcion
- EMI reduction circuitry
